A place for majestic STEMLORD peacocking, as well as memes about the realities of working in a lab.
Rules
This is a science community. We use the Dawkins definition of meme.
I'm dying chat.
Credit: An anonymous labrat friend. Thank you.
You know, I used to do this as a teenager, when cleaning my bearings with acetone, and I recall my family needing to get the sink repaired due to leakages getting quite severe at times.
Only through this post have I come to realise, 20 years later, that I was most likely at fault for the issue.
I mean I'm still not going to admit it to anyone, but it's good to know and stuff.
I had a bong as a freshman. I cleaned it with acetone. I then had several tubes instead.
Never understood why folks used acrylic bongs, like, how do you clean it? I kinda figured they were meant as disposable party bongs.
90%+ rubbing alcohol and rock salt actually does a really good job, it just takes more elbow grease. Still won't be as clean as literally fucking dissolving it, but that's how I'd do it if I couldn't use acetone.
I use 70% isopropyl and it dissolves everything except for a film around the inner chamber.
Like a lump of tar just stops existing as a solid thing. Looks interesting after like 6 hours.
70% is better for disinfectant, as the water helps carry the alcohol across the cell membrane.
90+ works better to dissolve bong residues, and the coarse salt works as an abrasive
The gold standard for party bongs is shitpipes. Dunno about other places but for a Euro standard one, you need, bottom to top, 1x 100mm end cap, 1x 100mm sleeve (pipe to pipe coupling), 1x 100mm adapter to 40mm (the 100mm side should fit the sleeve), some length of 40mm pipe, some means to drill two holes, and two things not available at any random hardware store: a preferably metal what's it called in English the thing that goes into the water and some tissue to tighten that metal thing in its hole, wrap in a taper and twist in. Try to get an adapter that's angled, there's also ones with a flat step instead of (quite aggressively) tapering the diameter.
Completely and utterly indestructible at least when it comes to banging it up. In principle also fit to handle acetone those Euro standard pipes are polypropylene but I wouldn't push it. Tons of water in there, definitely bottom-heavy, and very light when empty.
You really don't clean it you let it get gunky, just replace the water, it's not like the gunk would dissolve into there. If you really have to, just spend what five to ten bucks on new hardware. Euro pipes should in principle hold up to acetone they're PP but eh, why. If it works it's probably still going to make the thing unsable for a week or so.
Now that's science.
Back in the day we had a 50mm wide 1m long pipe. The bowl was on one end and the ends of the pipe were open. We would put some snow in it, the one person lit the bowl and plugged the end of the pipe with their palm while another person ripped until the pipe was full. Then the dude would move their hand and the other person would clear the pipe. It was so smooth with the snow in it. So smooth. I think it was called a steam roller or something. It was a long time ago.
Bucket bong has entered the chat.
I always thought the same, and I've been toking for about two decades. For pieces my friends and I always prefer glass. If using a glass piece though, it's important to use vinegar once in a while (not just Isopropanol) to get rid of the chance of mould build up.
Let's just all start smoking with acetone as our bong water! So many problems solved :)
At least you know why your sinks continue to melt now
Except admitting it to 50,000 lemmy users, haha. No worries, I didn't know acetone ruins pvc until this post either.
Your secret is safe with us Jaden
Context: acetone will dissolve ABS plastic. Drain pipes can be made out of ABS.
The pipes are usually made of PVC. Several other components are still often made of ABS.
In my experience, household drain pipes are usually made out of PVC.
True. I corrected the statement.
I mean, PVC pipes are even more vulnerable to acetone than ABS ones, so I would've made a different correction (broadening the statement rather than narrowing it).
That's just the natural aging process. Plumbing just gets saggy and wrinkly. Ask any man over 50.
I spent a bunch of time in art classes and learned more practical chemical safety and disposal than my actual chemistry classes.
Y'all have a sink in your fume hood? We just had waste bottles.
Cup sinks in fume hoods used to be more common, but as a lab planner they are pretty rare requests nowadays. If I had to guess, it's probably to do with the move away from central acid-waste neutralization systems towards procedural controls dictating neutralization/dilution prior to disposal.
Wait, industry is moving away from central neutralization? My wife is the facilities manager for an R1 engineering department and they commissioned a building two years ago with a central acid collection tank -_-
It varies from place to place, but the trend is away from them. I recently did a basis-of-design study for another R1 institution, and they said in no uncertain terms that they wanted to decommission the existing central system in their circa-1990 lab tower. Facilities departments often find them to be a PITA to manage and maintain, versus just requiring researchers to neutralize their acid waste before putting it down the sink, or collecting other hazardous waste to be taken away by a service
A lab planner! That's one of those cool (sounding at least) jobs that are obvious when you think about it but I've just never thought about it.
Definitely piqued my curiosity though. How much of your work is designing new labs vs retrofitting existing ones, how much travel is involved / how much area do you cover (the question there is really about how many labs exist needing such services), and what are any weird or surprising elements of your job?!
It's a niche specialization within architecture, and while I enjoy it it's not quite as cool as it sounds. Labs tend to be designed to a common template around the standard lab bench depth (30") and accepted safe aisle width between 66" and 72". Most of the fun is in equipment planning, and that's only exciting for a certain sort of Excel jockey 😅
Lab planning is a small enough niche that you really only find us in firms with a national or international reach, and so I'm more often working on projects several states away from me than anything in my own backyard. Travel varies, but other than initial meetings it tends to be hands-off job, so much so that I'm actually a 100% remote worker apart from when I'm on-site for a project kickoff or a site survey.
As for unusual or surprising parts of the job, I have really enjoyed working with some of the PI's I've fitted labs out for. The best has to be a chemist operating a biofuels testing lab, who regaled us with tales of all the times he'd blown up some glassware or singed off his eyebrows in the lab! I was a bit worried for his safety practices, though...
Ah interesting, I think for some reason I assumed it'd be more of an administrative career path offshoot for someone working in chemistry, but architecture does make more sense. And I know how you feel, I started my career in industrial controls because the idea of working at the interface between invisible electrical black magic and moving valves, motors, and other machinery seemed real cool.
Quickly learned that in that world, creativity and innovation are treated more like liabilities than anything else lol, and rightly so. There's a few great, proven ways to do most things, and rarely is it wise or fruitful to develop novel approaches over one of the proven solutions. I wouldn't want to be a chemist in a lab toting multiple new designs, lol.
I found it stifling, but could've tolerated it a lot better if the majority were WFH like yours!
A lot of ours has sinks, this wasn't at mine though. :)
Best way to get rid of acetone is what my boss made me and a co-worker do once:
Toss it onto some metal plates that had been left in 110 degree weather. They were also painted black.
Did you know that's enough for acetone to flash-light? We didn't until that moment, then we had fun
This is so irresponsible, everyone knows you pour it out outside.
into the gravel filled used oil pit?
Finally, an educated person up to date on the latest in popular science.
sounds like they need to a~~ce~~tone for their sins
Smelling it untill it's totally evaporated. Even if I much prefer isopropyl alcohol.
What is the proper disposal method?
Wick it with some paper towels and let it evaporate.
Acetone evaporates quickly. You just let it sit for a minute and it'll dispose of itself
so just inhale it all... ok
Yeah, I don't work in a lab, but if I clean something in the shop with Acetone, I leave the rag to dry on the side of the trash can. If I think it's a lot, I'll put it outside to evaporate or burn it.
I did a couple of times pour acetone down the drain but I did run water at full blast at the same time to wash it down immediately. Guess Im slightly smarter then undergrads.
the ol' dilute down the chute
EHS would raise hell if they caught us putting waste solvent in anything but a hazardous waste container...
Insane motherfuckers: "Pour the acetone in my mouth!"
Whichever one has the post polystyrene in it, right?
I fought hard to get a solvent extractor at my work. 11k paid for it's self in no time and almost no chemical disposal fees.
How else am I supposed to get rid of the agar huh?