r/startrek: The Next Generation
Star Trek news and discussion. No slash fic...
Maybe a little slash fic.
New to Star Trek and wondering where to start?
Rules
1 Be constructive
All posts/comments must be thoughtful and balanced.
2 Be welcoming
It is important that everyone from newbies to OG Trekkers feel welcome, no matter their gender, sexual orientation, religion or race.
3 Be truthful
All posts/comments must be factually accurate and verifiable. We are not a place for gossip, rumors, or manipulative or misleading content.
4 Be nice
If a polite way cannot be found to phrase what it is you want to say, don't say anything at all. Insulting or disparaging remarks about any human being are expressly not allowed.
5 Spoilers
Utilize the spoiler system for any and all spoilers relating to the most recently-aired episode. There is no formal spoiler protection for episodes/films after they have been available for approximately one week.
6 Keep on-topic
All busmittions must be directly about the Star Trek franchise (the shows, movies, books, etc.). Off-topic discussions are welcome at c/Quarks.
7 Meta
Questions and concerns about moderator actions should be brought forward via DM.
Upcoming Episodes
| Date | Episode | Title |
|---|---|---|
| 11-28 | LD 5x07 | "Fully Dilated" |
| 12-05 | LD 5x08 | "Upper Decks" |
| 12-12 | LD 5x09 | "Fissure Quest" |
| 12-19 | LD 5x10 | "The New Next Generation" |
| 01-24 | Film | "Section 31" |
In Production
Strange New Worlds (TBA)
Starfleet Academy (TBA)
In Development
Untitled comedy series
Wondering where to stream a series? Check here.
DS9 had at least two different kinds of flared mugs: the HotJo, which is still sold for $30, and the Feltman Langer, which is no longer sold, but this CherryTree is recreating.
Is this shape not rather impractical? It may be more difficult to accidentally knock over, but you would also need to tip it back to a somewhat extreme angle in order to get everything out of it.
I think the design was originally intended for use on boats, and other places where tipping is a likely occurrence.
I think it’s for any motor vehicle where tipping is likely. See this page with all sorts of pictures and examples, including old packaging.
Is the wider section actually hollow? I was imagining they might just have a normal round shape inside due to it being more difficult to mold.
It's very practical if you're somewhere without inertial dampeners.
Does earth have inertial dampeners??
No way am I able to clean that without a bottle brush. I'll sick to a standard mug.
Neat, a mug that looks like a bullhorn
I would not be able to properly control the flow rate of hot beverage directed at face with that design. Still love that look
Finally! Been looking for these for a long time that weren't stupidly overpriced!
They're 30 bucks...
It's still a lot of money for a mug, but compared to the $150-$300 they're selling for on eBay it's a great deal!
The jingle is a nice add-on, though a white-coloured print may have been clearer.
It's interesting that they didn't bother replicating (heh) the rubber base of the originals. Too many added costs, I suppose.
You’re probably right that the math didn’t add up for them.
Might be worth getting a pad replacement for the original cup and slapping that on yourself.
I wonder if those would fit - the article says that these "replimat-style" mugs are smaller than the Highwave "Quark's" mugs, but I suppose they could have the same base.
Very tempting! All the other ones I've seen are quite expensive.
Don't get me wrong, they get points for the Coolness Factor, but am I the only one who thinks this is genuinely a terrible design for a mug? Like, I have a hard enough time getting the coffee rings out of my cylindrical mugs, I don't even want to imagine the finger cramps I'd get trying to clean this one (or worse, the mold that would certainly grow if I didn't deep clean it every time)
I need this.
