thenewred

joined 1 year ago
[–] [email protected] 17 points 3 days ago (6 children)

Is there a bad taxidermy community?

[–] [email protected] 2 points 1 week ago

I might have crossed my wires, it was probably just a forum post I misread. I happened to have new ceramic burrs so I went ahead and installed them.

I got closer to a perfect pull this morning after adjusting the right lever! Unfortunately I'm out of that coffee now so the process restarts with the next bag.

[–] [email protected] 2 points 1 week ago* (last edited 1 week ago) (2 children)

New ceramic burrs.

I typically use light roast beans, apparently ceramic is better there.

Went through the hyperalignment procedure and got close but not perfect. Had to move on and get it back together at some point.

[–] [email protected] 2 points 1 week ago (1 children)

Works the same, just inline. And this grinder has two

[–] [email protected] 3 points 1 week ago* (last edited 1 week ago) (1 children)

I don't know about best, but these have been decent

Slurping Turtle (Easton)

Wild Ginger (Hilliard)

Aki Hana (Henderson)

 

Facepalm

[–] [email protected] 35 points 3 weeks ago (1 children)

Me writing my resume in third person

[–] [email protected] 22 points 3 weeks ago (1 children)

Is this comparing total number of visitors per year to inhabitants?

If so, it's a misleading graphic because visitors only stay for a week or two.

[–] [email protected] 2 points 3 weeks ago

A blessing! Free credit monitoring! All is well

[–] [email protected] 7 points 1 month ago (1 children)

Free solo*

But with a harness full of gear for extra weight reasons

And gloves because less grip == good?

[–] [email protected] 7 points 2 months ago

Me, spending hours on Age of Empires 2 and loving it

 
[–] [email protected] 28 points 3 months ago (3 children)

Janice from The Sopranos

[–] [email protected] 1 points 4 months ago

We water by soaking the plants in the tub, then letting them sit on towels before going back on the shelf. A bit tedious but only has to be done every 1-2 months.

 

Just learned about this. A long read, but really interesting.

 

Update to my previous post: https://lemmy.ca/post/7236274

 

I don't know why I even bother opening the settings app

 

Pretty happy with how this turned out, even months later

129
submitted 10 months ago* (last edited 10 months ago) by [email protected] to c/[email protected]
 

It's wild how similar woodworking and 3d printing are.

  1. Get a 3d printer
  2. Print things for the 3d printer

With woodworking

  1. Get a table saw
  2. Make things for the table saw

Now I can mix and match

Model: https://www.printables.com/model/205258-featherboard-with-replaceable-heads-m6

449
Belt organizer (lemmy.world)
submitted 10 months ago* (last edited 10 months ago) by [email protected] to c/[email protected]
71
submitted 10 months ago* (last edited 10 months ago) by [email protected] to c/[email protected]
 

Had minimal clearance between these overhead shelves and the garage door, and the perfect light spacing was a few inches away from the cross bars. So I designed these snap fit brackets to offset the lights inline.

The lights make a huge difference, much more pleasant to work in the garage.

What I learned:

  • there is some sag because the screws aren't at the top of the bracket. I would add a tab that protrudes on the side so I could add a screw higher.
  • the screw face split on layer lines on a few of these. Still works but not perfect, so I would make the screw face thicker.

Also printed cable management clips

view more: next ›