this post was submitted on 21 Jun 2023
24 points (100.0% liked)
Aotearoa / New Zealand
1656 readers
12 users here now
Kia ora and welcome to !newzealand, a place to share and discuss anything about Aotearoa in general
- For politics , please use [email protected]
- Shitposts, circlejerks, memes, and non-NZ topics belong in [email protected]
- If you need help using Lemmy.nz, go to [email protected]
- NZ regional and special interest communities
Rules:
FAQ ~ NZ Community List ~ Join Matrix chatroom
Banner image by Bernard Spragg
Got an idea for next month's banner?
founded 1 year ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
Yeah, I noticed it didn't do anything when set to e.g. 22c when it was already 22c there. Then I read the manual, which is a bit cryptical:
Notice the bold part. First it says, if the temp setting is higher/same as ambient, it will perform slightly below ambient. However, next sentence it says it stops when temp setting is higher/same as ambient?
I have to set it e.g. 2c lower than ambient, otherwise it just doesn't do anything
Yes I noticed it contradicted itself. I think that was probably referring to the earlier part, that you start it when the temperature is high then it keeps going until it reaches the set temperature.
I am going to go and play with ours now, we haven't really used that setting, but I have no idea what the humidity is in the house. I've just in the past in a different house had to work out how to reduce dampness and mould.
Yes, guess you're right.
I've got a cheap weather station from Aliexpress which also has a humidity sensor, that could be a temporary solution for you if you don't go for the HA route.
Nah, that takes the fun out of it. Given how cheap the parts are I'm going to have a play at getting HA set up when I get a chance.
Good luck!
One tip if you have a SO: Make sure that they are on board, and that it only adds benefits & there's a backup/fallback plan. E.g. don't say "Oh sorry the lights don't work if the internet is down", that won't go down well :)
Haha good point! What is the plan when that happens?
I'm avoiding plugs that require internet access, but it's a bit hard, especially in NZ. E.g. the TP Link smart plus don't work if the internet is down, and my standing desk is Tuya based which requires the cloud.
But, e.g. the TP Link plugs still have a button to turn them on manually in case the internet is down. The lights still work if you turn them off and back on at the wall. So everything can still work without internet.
Ok cool, I'll be sure to think about that stuff before getting too far along, thanks for the suggestion.
Most of the lights in our house are built in LED downlights, so can't really switch them out for smart bulbs, it would need to be a smart switch
Yeah it's a big rabbit hole like I suggested. I am also looking at automating our "dumb" alarm, our garage door, our Nissan Leaf, etc. I'm no longer allowed to talk about it during dinner, so please take it slowly :)
Just to add, it IS very handy. I've just created a script that sets the heat pump to Dry & 2c lower than ambient temperature.
This way I will be able to create automations to e.g. run it on Dry every night for e.g. an hour, then back to heat, etc.
This sounds like a rabbit hole I'd like to get lost in. Except when I'm away and no one else can use anything because I stupidly started an update just before I needed to leave and it broke things and now nothing is working.
Yep, try to do small things first instead of letting hell go loose if something doesn't work.
I've set up a tablet in the living room as "wall panel" where e.g. the kids can change the thermostat for their bedrooms, check the weather forecast, and it shows random photos from the NAS as a screensaver, which is just fun & nice.
That's cool! I like that idea.
What is something simple to start with if getting into HA? I already have a NAS.
I started with:
Next to do is put smart plugs in our electric blankets, make our dumb alarm smart and make the garage door smart.
You can run it dockerized to get started.
Oh cool. I'm going to try the temp sensors. Thank you!
Enjoy. It's a rabbit hole, I've just spent hours googling for a Zigbee IR blaster that's compatible with ZHA, and there's none. Zigbee2MQTT has better compatibility but I don't want to convert my Zigbee network to Z2M at the moment.