micromobility - Ebikes, scooters, longboards: Whatever floats your goat, this is micromobility
Ebikes, bicycles, scooters, skateboards, longboards, eboards, motorcycles, skates, unicycles: Whatever floats your goat, this is all things micromobility!
"Transportation using lightweight vehicles such as bicycles or scooters, especially electric ones that may be borrowed as part of a self-service rental program in which people rent vehicles for short-term use within a town or city.
micromobility is seen as a potential solution to moving people more efficiently around cities"
Feel free to also check out
It's a little sad that we need to actually say this, but:
Don't be an asshole or you will be permanently banned.
Respectful debate is totally OK, criticizing a product is fine, but being verbally abusive will not be tolerated.
Focus on discussing the idea, not attacking the person.
view the rest of the comments
This is generally not a thing.
Generally no. DIY ebikes from good components are easier to repair but not without spare parts. Good luck with that during an apocalypse. Cheap factory ebikes as well as expensive factory bikes with mid drives aren't repairable. Finding parts is a problem with the former (today, not in an apocalypse), the other can only be repaired by authorised shops due to parts and DRM.
As others mentioned, batteries may not last too long depending on the make and chemistry. A LFP based DIY would likely last the longest. You have to keep a few spares of all parts - controller, motor, computer, and a spare battery.
Regen is a fairly common feature in ebikes. It doesn't work while you ride, other than as a brake going down hills, but as most are hub drive if you lift the rear wheel off the ground you could use the bike as a generator and charge the battery by pedalling.
However, it would in no way be energy (food) efficient compared to just using a bicycle due to the losses, but if you needed it for emergencies or for powering something else, it could be used.
It's not a common feature.
It doesn't make as much sense to do on an bike, mainly because regenerative breaking requires more expensive electronics and stresses the battery more.
My family has 7 ebikes, all different models and none has regen.
It's not common, but it does make sense to do! No, not in charging the battery but in braking. Regen slows down the bike without wearing down your brake pads, which is extra important with a heavy bike. I cannot even manage 900 miles without changing my longtail's pads. I have yet to replace the pads on my regenerating e-trike.
The extra 20% range is nice but I'm more happy about the money and hassle I've saved in not replacing brake pads.
You can't slow down with regen without putting the energy somewhere, and that's the point of brakes, they convert kinetic energy into thermal to slow you down.
The point of regen is to not waste the energy and put most of it back into a battery. At the scale of an ebikes, the additional components electronics, battery thermal management, and so on for regen are more expensive than just adding 20% more battery.
Unless you wanted to make an expensive, super efficient or very light ebike, it just doesn't make sense at the moment.
That will not likely always be true if we ever use different battery chemistry and the cost of regen electronics goes down.
I agree it doesn't make sense to pick regen for extending range. Just buy a bigger battery if that's the biggest issue, say a rarely used bike but long ranged when needed.
To me it's the brake pads that add up. Replacing two pairs of pads every few hundred miles is way more expensive than the system and any additional battery wear. $500 isn't that many sets of pads.
Considering I don't charge my batteries much beyond 80%, yeah, there's plenty of room to put that extra energy early in the ride. I'd rather charge a battery than to grind pads into dust.
Honestly I'd wonder if the wear on brake pads could be cheaper than the additional strain on the battery.
I have 1400 miles on my non-regen bike which has burned through three sets of pads (1.5 mm currently left). I'm slowly trying better/harder pads which won't eat rotors and don't cost as much. $25 every 500-ish miles isn't great (10k miles is $500 in pads) . Suggestions are welcome!
I think a key difference is my neighborhood is quite hilly. I've never smoked and glazed a set of pads before moving in. That was a quick learning experience for me.
Maybe a super cap, to better handle the charge rate?